Tektronix P6021 Current Probe 125 Turns

Tektronix P6021 AC Current Probe 125 Turns

ORIGINAL COSTS

Tektronix Catalog Cost	Low Bid	High Bid	average
$110 (passive term), $295 (w/ 134 Amp) (1969-new) $129 (passive term), $323 (w/ 134 Amp) (1973) $185 (passive term), $535 (w/ 134 Amp) (1977) $295 (passive term), $835 (w/ 134 Amp) (1982) $388 (passive term), $1013 (w/ 134 Amp) (1985) $450 (passive term), $1120 (w/ 134 Amp) (1989) $630 (1998) $1200 (passive term) (1/2008)	.	.	.
$158.00 7/27/01 #1618929531 calibrat1 (with termination) $202.52 8/04/01 #1621593521 roglinx (with amplifier & case) $102.50 8/8/01 #1622939502 outback6 (with termination) $117.51 8/8/01 #1622972581 cieinternational (with termination) $71.00 1/11/03 #3105140198 netsales1 (with termination) (9 bids $10 start) $182.50 1/24/03 #3108712816 netsales1 (35 bids $10 start) $127.65 (+~$14 ship) 2/8/08 #220198074804 anainstr (13 bids $9.99 start) (with termination) $157.50 (+$8 ship) 2/10/08 #320214763640 cantfixthis (14 bids $0.99 start) (with termination-working when last used) $137.50 (+$5.85 ship) 6/5/09 #170337388740 jsas2009 (22 bids $24.99 start) (with termination - untested) $168.39 (Free Ship) 11/9/10 #160501561461 ramtech39053 (6 bids $99.99 start) (with termination - functions as intended)

QUICK SPECS / PHOTOS

Bandwidth : 450 Hz to 60 MHz (10 mA/mV)

120 Hz to 60 MHz (2 mA/mV)

Pulse Rise Time : ≤5.8 ns

Sensitivity : 2 mA or 10 mA for each mV at oscilloscope input, selected by termination sensitivity control.

Insertion Impedance : 0.03Ω or less at 1 MHz

Maximum Conductor Diameter : 0.141"

Readout Pin : NO

Ground Ref : n/a

ID Button : NO

Max Rated Current : 5A(p-p) RMS (2 mA/mV)

15A(p-p) RMS (10 mA/mV)

Max Rated Voltage : 300 VRMS

Cable Length : 5 ft or 9 ft

Net Weight : 3.6 oz (103 gm) (w/5 ft cable)

4.4 oz (125 gm) (w/9 ft cable)

1.7 oz (48 gm) for Termination

Scope Compatibility : Most General Purpose

The P6021 current probe converts an alternating current waveform to a voltage that can be displayed and measured on an oscilloscope display. The probe provides accurate current measurements over a wide range of frequencies, and allows you to measure current without breaking the circuit.

The P6021 probe is compatible with general purpose oscilloscopes having a 1 MΩ input impedance. The P6021 probe comes with a passive termination that matches oscilloscope and probe impedance, optimizes the probe performance, and provides two sensitivity settings.

In the standard configuration, the P6021 probe comes with a 5-foot cable and termination. The following option is also available.

Option 03 - 9-foot cable with termination

The P6021 current probe consists of a curent transformer mounted in the nose of the probe head case, an impedance-matching network, and an internal switch to disconnect the transformer shield from ground.

As indicated on the probe body, the turns ratio of the P6021 is 125:1. This refers to the number of windings in the secondary of the probe transformer.

The P6021 termination consists of a 62.5Ω impedance-matching network to terminate the coaxial cable and a voltage divider that is switched in by a sensitivity control to change the sensitivity by a factor of five.l When the control is n the 2 mA/mV position, a 10 mA current signal in the conductor under test induces a 5 mV signal at the output of the termination. (This assumes that the termination is connected to a 1 MΩ input oscilloscope.)

When the sensitivity control is in the 10 mA/mV position, a 10 mA current signal is attenuated to induce a 1 mV signal at the output of the termination.

(above excerpts from Tektronix® Products Instruction Manual 070-0947-05 for P6021)

COMPATIBILITY

CHARACTISTICS

SPECIFICATIONS

SAMPLES OF E-BAY PRICES